2003 Mitsubishi Lancer Evolution Factory Service Manual
- Home
- Cars
- Mitsubishi
- 2003 Mitsubishi Lancer Evolution Service Manual
Original 2003 Mitsubishi Lancer Evolution Factory Service Manual
To find information in PDF file please use "Ctrl+F" or "Command+F" for Mac and enter keywords you need to find in a manual.
File will be available for download in minutes!
"2003 Mitsubishi Lancer Evolution Factory Service Manual" manual can be saved to any computer hard drive, flash storage, burned to a CD or DVD ROM or any other digital media.This Manual PDF file is:
- + Printable: Yes
- + Viewable on: MS Windows, Mac, Android, iOS, Linux
- + Requires: Adobe Acrobat/Preview
Once manual is downloaded any number of pages could be printed or it could be printed in whole.
Manual could be opened in Adobe Acrobat on any mobile device (like iPad, iPhone or Android device etc.) any computer capable of viewing a PDF files including IBM compatible computers running Windows, Linux (or any other flavor of UNIX). Apple Computers have native support for PDF files.
Write a Review
Full list of manual chapters:
Mitsubishi_Lancer_Evo_2003-General_Info_1
Mitsubishi_Lancer_Evo_2003-General_Info_2
Mitsubishi_Lancer_Evo_2003-Additional_Info_1
Mitsubishi_Lancer_Evo_2003-Additional_Info_2
Mitsubishi_Lancer_Evo_2003-Chassis_Part_1
Mitsubishi_Lancer_Evo_2003-Chassis_Part_2
Mitsubishi_Lancer_Evo_2003-Drivetrain_Part_1
Mitsubishi_Lancer_Evo_2003-Drivetrain_Part_2
Mitsubishi_Lancer_Evo_2003-Emission
Mitsubishi_Lancer_Evo_2003-Engine
Mitsubishi_Lancer_Evo_2003-Body
BODY CONSTRUCTION
BODY COMPONENTS
BODY MAIN CROSS-SECTIONAL VIEWS
MAINTENANCE, SERVICEABILITY
FENDER SHIELD
SIDE STRUCTURE
SIDE OUTER PANEL
BODY CONSTRUCTION CHARACTERISTICS
HEADLAMP SUPPORT
FENDER SHIELD
RIGHT SIDE
LEFT SIDE
FRONT DECK
DASH PANEL
SIDE STRUCTURE REINFORCEMENT
FRONT FLOOR
SILENCER APPLICATION LOCATIONS
LOCATIONS USING URETHANE FOAM AND FOAM MATERIAL
STIFFENER AND DAMP SHEET APPLICATION LOCATIONS
THEFT PROTECTION
GR00000700-5
SYNTHETIC-RESIN PARTS
LOCATION OF SYNTHETIC-RESIN PARTS
GR00000500-3
WELDED PANEL REPLACEMENT
HEADLAMP SUPPORT
FENDER SHIELD
FRONT SIDEMEMBER (PARTIAL REPLACEMENT)
NOTE ON REPAIR WORK
FRONT PILLAR
NOTE ON REPAIR WORK
INSTALLATION <Vehicles with sunroof>
CENTER PILLAR
NOTE ON REPAIR WORK
INSTALLATION
SIDE SILL
NOTE ON REPAIR WORK
INSTALLATION
QUARTER OUTER
NOTE ON REPAIR WORK
ROOF
REAR END PANEL
REAR FLOOR
NOTE ON REPAIR WORK
QUARTER INNER
QUARTER INNER (PARTIAL REPLACEMENT)
NOTE ON REPAIR WORK
INSTALLATION
FRONT DOOR OUTER PANEL
REAR DOOR OUTER PANEL
ALUMINUM PANEL
Description of aluminum panel
Advantage of aluminum panel
ALUMINUM PANEL REPAIR
Items to be noted when working on sheet metal
Correction of uneven surface
Correction of cuts and cracks
MIG welding
TIG welding
Finish with putty
ALUMINUM PANEL PAINT
Painting in production line
Repair painting
GR00000400-2
BODY DIMENSIONS
BODY DIMENSIONS AND MEASUREMENT METHODS
TYPE A (PROJECTED DIMENSIONS)
TYPE B (ACTUAL-MEASUREMENT DIMENSIONS)
GR00000800-6
BODY COLOR
BODY COLOR CODE
BODY COLOR CHARTS
BODY COLORING
GR00000600-4
CORROSION PROTECTION
BODY SEALING LOCATIONS
FLOOR
UPPER BODY
SIDE BODY
UNDERCOAT APPLICATION LOCATIONS
UNDERBODY ANTICORROSION AGENT LOCATIONS
GR00001200-7
WIRING AND PIPING DIAGRAM
PIPING DIAGRAM
GR00001000-9
BASE OF BODY REPAIR
WELDING
FUSION WELDING
PRESSURE WELDING
BRAZING
ADVANTAGES OF ELECTRIC RESISTANCE SPOT WELDING
PROCEDURE
NUGGET FORMATION
NOTES REGARDING WELDING
WELDING REQUIREMENTS
Galvanized steel plate (SECC)
USING A TEST PIECE TO CHECK NUGGET FORMATION
CHECKING NUGGET STRENGTH FOLLOWING SPOT WELDING
Procedure
FEATURES OF MIG SPOT WELDING
PLUG WELDING
CONTINUOUS WELDING
Torch angle and welding technique
Preventing warping
NOTES REGARDING MIG WELDING
BRAZING
Notes with regard to brazing work
GAS WELDING
Notes with regard to gas welding
BODY REPAIR
STANDARD PROCEDURES FOR REPLACEMENT OF WELDED PANELS
CAUTIONS REGARDING BODY REPAIR
STRENGTH AND RIGIDITY
SAFETY
PREVENTION OF CORROSION AND OF WATER OR DUST ENTRY
VIBRATION AND NOISE
CONTACT AND ALIGNMENT
THEFT PROTECTION
PANEL REPAIR CAUTION
HOW TO PEEL OFF THE SURFACE MASKING FILM FROM THE THEFT-PROTECTION LABEL
REPAIRS USING A HAMMER AND DOLLY
OVERALL ROUGH REPAIRS
FRAME STRAIGHTENING NOTES
CHECKING FOR FRAME CRACKING OR FLANKING
REPAIRING CRACKS
NOTES REGARDING REPAIR WORK
SAFETY MEASURES
PROTECTIVE GEAR
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
SECURING THE VEHICLE
CLEARING THE AREA OF FLAMMABLE MATERIALS
HANDLING ELECTRONIC PARTS AND SEMICONDUCTORS
HANDLING COMBUSTIBLE MATERIALS
HEALTH AND SANITATION PROCEDURES
VEHICLE PROTECTION
CORROSION PROTECTION
ZINC PHOSPHATE COATING
BODY SEALING
UNDERBODY COATING
WAX INJECTION
SEALING TAPE
ANTICORROSION TREATMENT AT THE TIME OF BODY REPAIR WORK
CORROSION PROTECTION FOR HOLLOW PARTS
ANTICORROSION TREATMENT OF ROUGH CUTS
SPOT SEALER
SPOT SEALER APPLICATION STEPS
BODY SEALING
GR00000900-8
REFERENCE MATERIAL
BOLTED PANEL FIT AND ADJUSTMENT
HOOD
ADJUSTMENT OF HOOD FIT
DOOR
ADJUSMENT OF DOOR FIT
TRUNK LID
ADJUSTMENT OF TRUNK LID FIT
FUEL FILLER LID
ADJUSTMENT OF FUEL FILLER LID FIT
INSTALLATION AND REMOVAL OF ADHESIVE COMPONENTS
ADHESIVE TAPE POSITION
REMOVAL
INSTALLATION
ADJUSTMENT OF OTHER PARTS
FRONT WHEEL ALIGNMENT
TOE-IN
CAMBER, CASTER AND KINGPIN INCLINATION
REAR WHEEL ALIGNMENT
TOE-IN
CAMBER
HEADLIGHT AIMING
PRE-AIMING INSTRUCTIONS
HEADLIGHT ADJUSTMENT
FOG LIGHT AIMING
PRE-AIMING INSTRUCTIONS
FOG LIGHT ADJUSTMENT
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) - AIR BAG
Mitsubishi_Lancer_Evo_2003-MFI_1a
Mitsubishi_Lancer_Evo_2003-MFI_1b
Mitsubishi_Lancer_Evo_2003-MFI_2a
Mitsubishi_Lancer_Evo_2003-MFI_2b
Mitsubishi_Lancer_Evo_2003-MFI_3
Mitsubishi_Lancer_Evo_2003-SRS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
GENERAL DESCRIPTION
ON-BOARD DIAGNOSTIC/SRS WARNING LIGHT FUNCTION
WARNING/CAUTION LABELS
SRS air bag special connector
SQUIB CIRCUIT CONNECTOR LOCK SWITCH
WARNING LIGHT CIRCUIT CONNECTOR LOCK SWITCH
SERVICE PRECAUTIONS
SRS AIR BAG DIAGNOSIS
DIAGNOSTIC FUNCTION
HOW TO CONNECT THE SCAN TOOL
<When using scan tool MB991502>
<When using scan tool MB991958>
HOW TO READ AND ERASE DIAGNOSTIC TROUBLE CODES
<When using scan tool MB991502>
<When using scan tool MB991958>
SRS WARNING LIGHT CHECK
DIAGNOSTIC TROUBLE CODE PROCEDURES
CIRCUIT OPERATION
DTC SET CONDITIONS
DIAGNOSIS
Step 1. Check the front impact sensor.
Step 2. Measure the resistance and voltage at SRS-ECU connector C-12.
Step 3. Check the wiring harness between the right front impact sensor connector A-37 (terminals .
Step 4. Recheck for diagnostic trouble code.
DIAGNOSIS
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HINTS
DIAGNOSIS
STEP 1. Using scan tool MB991502 or MB991958, read the diagnostic trouble code.
STEP 2. Check SRS-ECU connector C-12.
STEP 3. Check SRS-ECU connector C-12, clock sprin
STEP 4. Check the driver's air bag module.
STEP 5. Check the clock spring.
STEP 6. Check the driver's air bag module circuit
STEP 7. Check the harness for short circuit between SRS- ECU connector C-12 (terminal No.11 and 1.
STEP 8. Recheck for diagnostic trouble code.
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HINTS
DIAGNOSIS
STEP 1. Check the driver's air bag module.
STEP 2. Check the clock spring.
STEP 3. Check the harness between the SRS-ECU connector C-12 (terminal No.11 and 12) and the cloc.
STEP 4. Recheck for diagnostic trouble code.
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HINTS
DIAGNOSIS
STEP 1. Using scan tool MB991502 or MB991958, read the diagnostic trouble code.
STEP 2. Check SRS-ECU connector C-12.
STEP 3. Check SRS-ECU connector C-12 and passenge
STEP 4. Check the passenger's air bag module.
STEP 5. Check the passenger's air bag module circuit at SRS-ECU connector C-12.
STEP 6. Check the harness for short circuit between SRS- ECU connector C-12 (terminal No.9 and 10.
STEP 7. Recheck for diagnostic trouble code.
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HINTS
DIAGNOSIS
STEP 1. Check the passenger's air bag module.
STEP 2. Check the harness for open circuit between SRS- ECU connector C-12 (terminal No.9 and 10).
STEP 3. Recheck the diagnostic trouble code.
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HITS
DIAGNOSIS
STEP 1. Using scan tool MB991502 or MB991958, read the diagnostic trouble code.
STEP 2. Check the SRS-ECU connector C-13.
STEP 3. Check SRS-ECU connector C-13 and driver's
STEP 4. Check the driver's seat belt pre-tensioner.
STEP 5. Check the driver's seat belt pre-tensione
STEP 6. Check the harness for short circuit between SRS- ECU connector C-13 (terminal No.29 and 3.
STEP 7. Recheck for diagnostic trouble code.
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HITS
DIAGNOSIS
STEP 1. Check the driver's seat belt pre-tensioner.
STEP 2. Check the harness for open circuit between SRS- ECU connector C-13 (terminal No.29 and 30.
STEP 3. Recheck for diagnostic trouble code.
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HITS
DIAGNOSIS
STEP 1. Using scan tool MB991502 or MB991958, read the diagnostic trouble code.
STEP 2. Check the SRS-ECU connector C-13.
STEP 3. Check SRS-ECU connector C-13 and passenge
STEP 4. Check the passenger's seat belt pre-tensioner.
STEP 5. Check the passenger's seat belt pre-tensioner circuit at the SRS-ECU connector C-13.
STEP 6. Check the harness for short circuit between SRS- ECU connector C-13 (terminal No. 27 and .
STEP 7. Recheck for diagnostic trouble code DTC.
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HITS
DIAGNOSIS
STEP 1. Check the passenger's seat belt pre-tensioner.
STEP 2. Check the harness for open circuit between SRS- ECU connector C-13 (terminal No.27 and 28.
STEP 3. Recheck for diagnostic trouble code.
DTC SET CONDITIONS
TROUBLESHOOTING HINTS
DIAGNOSIS
STEP 1. Check the SRS-ECU connector C-12, C-13.
STEP 2. Check SRS-ECU connector C-12, C-13 for damage.
STEP 3. Recheck the diagnostic trouble code.
DTC SET CONDITIONS
TROUBLESHOOTING HINTS
DIAGNOSIS
TROUBLE JUDGMENT
Possible causes
Diagnosis
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HINTS
DIAGNOSIS
STEP 1. Check junction block fuse number 2.
STEP 2. Check the power supply circuit for open circuit at the SRS-ECU connector C-12.
STEP 3. Check the harness for open circuit between SRS- ECU connector C-12 (terminal No.16) and t.
STEP 4. Check a burned-out fuse.
STEP 5. Check the SRS-ECU power supply circuit for short circuit to ground at the junction block .
STEP 6. Check the fuse number 2-related circuit at junction block connector C-214.
STEP 7. Check the harness for short circuit to ground between junction block connector C-214 (ter.
STEP 8. Check the power supply circuit for short circuit to ground at the SRS-ECU connector C-12.
STEP 9. Check the harness for short circuit to ground between SRS-ECU connector C-12 (terminal No.
STEP 10. Recheck for diagnostic trouble code.
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HINTS
DIAGNOSIS
STEP 1. Check junction block fuse number 3.
STEP 2. Check the power supply circuit harness for open circuit at the SRS-ECU connector C-12.
STEP 3. Check the harness for open circuit between SRS- ECU connector C-12 (terminal No.13) and t.
STEP 4. Check a burned-out fuse.
STEP 5. Check the SRS-ECU power supply circuit for short circuit to ground at the junction block .
STEP 6. Check the power supply circuit for short circuit to ground at the SRS-ECU connector C-12.
STEP 7. Check the harness for short circuit to ground between SRS-ECU connector C-12 (terminal No.
STEP 8. Recheck for diagnostic trouble code.
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HINTS
DIAGNOSIS
STEP 1. Check the SRS warning light.
STEP 2. Check the ground line at the SRS-ECU connector C-12.
STEP 3. Check the SRS warning light bulb.
STEP 4. Check the harness for open circuit between ignition switch connector C-208 (terminal No.2.
STEP 5. Check the harness for open circuit between SRS- ECU connector C-12 (terminal No.7) and gr.
STEP 6. Recheck for diagnostic trouble code.
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HINTS
DIAGNOSIS
STEP 1. Check SRS-ECU connector C-12 for damage.
STEP 2. Check the SRS warning light.
STEP 3. Check the harness for short circuit to ground between SRS-ECU connector C-12 (terminal No.
STEP 4. Recheck for diagnostic trouble code.
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HINTS
DIAGNOSIS
STEP 1. Check the SRS warning light drive circuit system. Refer to P.52B-111.
STEP 2. Recheck for diagnostic trouble code.
GR00007200B-52B
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
SRS AIR BAG DIAGNOSIS
DIAGNOSTIC TROUBLE CODE PROCEDURES
TROUBLE JUDGMENT
Possible causes
DIAGNOSIS
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HINTS
DIAGNOSIS
STEP 1. Check the driver's air bag module.
STEP 2. Check the clock spring.
STEP 3. Check the driver's air bag module circuit
STEP 4. Check the harness for short circuit to power supply between SRS-ECU connector C-12 (termi.
STEP 5. Recheck for diagnostic trouble code.
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HINTS
DIAGNOSIS
STEP 1. Check the driver's air bag module.
STEP 2. Check the clock spring.
STEP 3. Check the driver's air bag module circuit
STEP 4. Check the harness for short circuit to ground between SRS-ECU connector C-12 (terminal No.
STEP 5. Recheck for diagnostic trouble code.
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HINTS
DIAGNOSIS
STEP1. Check the passenger's air bag module.
STEP 2. Check the passenger's air bag module circuit at the SRS-ECU connector C-12.
STEP 3. Check the harness wires for short circuit to power supply between SRS-ECU connector C-12 .
STEP 4. Recheck for diagnostic trouble code.
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HINTS
DIAGNOSIS
STEP 1. Check the passenger's air bag module.
STEP 2. Check the passenger's air bag module circuit at the SRS-ECU connector C-12.
STEP 3. Check the harness wires for short circuit to ground between SRS-ECU connector C-12 (termi.
STEP 4. Recheck for diagnostic trouble code.
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HITS
DIAGNOSIS
STEP 1. Check the driver's seat belt pre-tensioner.
STEP 2. Check the driver's seat belt pre-tensioner circuit at the SRS-ECU connector C-13.
STEP 3. Check the harness wires for short circuit to power supply between SRS-ECU connector C-13 .
STEP 4. Recheck for diagnostic trouble code.
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HITS
DIAGNOSIS
STEP 1. Check the driver's seat belt pre-tensioner.
STEP 2. Check the driver's seat belt pre-tensioner circuit at the SRS-ECU connector C-13.
STEP 3. Check harness wires for short circuit to ground between SRS-ECU connector C-13 (terminal .
STEP 4. Recheck for diagnostic trouble code.
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HITS
DIAGNOSIS
STEP 1. Check the passenger's seat belt pre-tensioner.
STEP 2. Check the passenger's seat belt pre-tensioner circuit at the SRS-ECU connector C-13.
STEP 3. Check the harness wires for short circuit to power supply between SRS-ECU connector C-13 .
STEP 4. Recheck for diagnostic trouble code.
CIRCUIT OPERATION
DTC SET CONDITIONS
TROUBLESHOOTING HITS
DIAGNOSIS
STEP 1. Check the passenger's seat belt pre-tensioner.
STEP 2. Check the passenger's seat belt pre-tensioner circuit at the SRS-ECU connector C-13.
STEP 3. Check harness wires for short circuit to ground between SRS-ECU connector C-13 (terminal .
STEP 4. Recheck for diagnostic trouble code.
SYMPTOM PROCEDURES
CIRCUIT OPERATION
TECHNICAL DESCRIPTION (COMMENT)
TROUBLESHOOTING HINTS
DIAGNOSIS
STEP 1. Check that the scan tool can communicate with the other systems.
STEP 2. Check the communication line between the SRS- ECU and the scan tool.
STEP 3. Check the ground circuit to the SRS-ECU.
STEP 4. Check the power supply circuit to the SRS-ECU.
STEP 5. Check the harness wires between SRS-ECU connector C-12 (terminal No.20) and data link con.
STEP 6. Check the harness wire between SRS-ECU connector C-12 (terminal No.7) and ground.
STEP 7. Check the harness wires between SRS-ECU connector C-12 (terminal No.13 and 16) and igniti.
STEP 8. Retest the system.
SPECIAL TOOLS
TEST EQUIPMENT
SRS MAINTENANCE
POST-COLLISION DIAGNOSIS
SRS-ECU MEMORY CHECK
REPAIR PROCEDURE
WHEN AIR BAGS DO NOT DEPLOY IN LOW-SPEED COLLISION.
Front impact sensor
SRS-ECU
Air bag modules
Clock spring
Steering wheel, steering column and shaft assembly
Seat belt with pre-tensioner
Harness connector (floor wiring harness)
INDIVIDUAL COMPONENT SERVICE
FRONT IMPACT SENSORS
REMOVAL SERVICE POINT
INSTALLATION SERVICE POINTS
>>B<< FRONT IMPACT SENSOR INSTALLATION
>>C<< POST-INSTALLATION INSPECTION
INSPECTION
SRS CONTROL UNIT (SRS-ECU)
REMOVAL SERVICE POINT
INSTALLATION SERVICE POINTS
>>B<< POST-INSTALLATION INSPECTION
INSPECTION
AIR BAG MODULE(S) AND CLOCK SPRING
REMOVAL SERVICE POINT
<<B>> COVER REMOVAL
<<C>> STEERING WHEEL-DRIVER'S AIR BAG MODULE ASSE
<<D>> CLOCK SPRING REMOVAL
<<E>> AIR BAG MODULE REMOVAL (FRONT PASSENGER'S S
INSTALLATION SERVICE POINTS
>>B<< CLOCK SPRING INSTALLATION
>>C<< STEERING WHEEL-DRIVER'S AIR BAG MODULE ASSE
>>D<< POST-INSTALLATION INSPECTION
INSPECTION
AIR BAG MODULE CHECK
CLOCK SPRING CHECK
SEAT BELTS WITH PRE-TENSIONER
REMOVAL SERVICE POINTS
<<B>> PRE-TENSIONER CONNECTOR DISCONNECTION
INSTALLATION SERVICE POINTS
>>B<< PRE-TENSIONER CONNECTOR CONNECTION
>>C<< POST-INSTALLATION INSPECTION
INSPECTION
SEAT BELT WITH PRE-TENSIONER CHECK
AIR BAG MODULE AND SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES
UNDEPLOYED AIR BAG MODULE DISPOSAL
DEPLOYMENT INSIDE THE VEHICLE (when disposing of a vehicle) <Air bag module (driver's side)>
DEPLOYMENT INSIDE THE VEHICLE (when disposing of a vehicle) <Air bag module (front passenger's si.
DEPLOYMENT INSIDE THE VEHICLE (when disposing of a vehicle) <Seat belt pre-tensioner>
DEPLOYMENT OUTSIDE THE VEHICLE <Air bag module (driver's side)>
DEPLOYMENT OUTSIDE THE VEHICLE <Air bag module (front passenger's side)>
DEPLOYMENT OUTSIDE THE VEHICLE <Seat belt pre- tensioner>
DEPLOYED AIR BAG MODULE AND OPERATED SEAT BELT PRE-TENSIONER DISPOSAL
SPECIFICATIONS
Mitsubishi_Lancer_Evo_2003-SWS_1
Mitsubishi_Lancer_Evo_2003-SWS_2
Mitsubishi_Lancer_Evo_2003-Wiring
CIRCUIT DIAGRAMS
HOW TO READ CIRCUIT DIAGRAMS
WIRE COLOR CODES
JUNCTION BLOCK
JOINT CONNECTOR
CENTRALIZED JUNCTION
FUSIBLE LINK AND FUSE
POWER DISTRIBUTION SYSTEM
STARTING SYSTEM
IGNITION SYSTEM
CHARGING SYSTEM
MFI SYSTEM
COOLING SYSTEM
HEADLIGHT
HEADLIGHT LEVELING SYSTEM
TAILLIGHT, POSITION LIGHT, SIDE MARKER LIGHT AND LICENSE PLATE LIGHT
DOME LIGHT,LUGGAGE COMPARTMENT LIGHT AND IGNITION KEY CYLINDER ILLUMINATION LIGHT
FOG LIGHT
HORN
STOPLIGHT
BACKUP LIGHT
TURN SIGNAL LIGHT AND HAZARD WARNING LIGHT
METER AND GAUGE
BRAKE WARNING LIGHT, OIL WARNING LIGHT, FUEL WARNING LIGHT
POWER WINDOWS
CENTRAL DOOR LOCKING SYSTEM
MANUAL AIR CONDITIONING SYSTEM
REMOTE CONTROLLED MIRROR
WINDSHIELD WIPER AND WASHER
REAR WINDOW DEFOGGER
REAR WIPER AND WASHER
CLOCK
AUDIO SYSTEM
CIGARETTE LIGHTER
ANTI-LOCK BRAKING SYSTEM(ABS)
SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
CHARGE AIR COOLER WATER SPLAY SYSTEM
IMMOBILIZER SYSTEM
LIGHTING MONITOR TONE ALARM
SEAT BELT WARNING LIGHT
IGNITION KEY REMINDER TONE ALARM
SUNROOF
RHEOSTAT
